Open this section to check available listings. No listing request is made until you open it.
Source: Car Handshake and participating dealerships. Year, make and model must match to appear here; trims and specifications can differ. Listings do not establish vehicle condition or recall repair status.
Reported Problem Categories
US NHTSA complaints for the 2013 Ford Explorer.
STEERING
837
STRUCTURE
439
UNKNOWN OR OTHER
345
ENGINE
226
ELECTRICAL SYSTEM
163
NHTSA documents known discrepancies in its bulk complaint file. Consumer allegations are not confirmed defects. One complaint can mention several categories. Counts are not failure rates.
At a Glance
Source configurations, without assumed specifications.
US campaigns received since 2010; not a complete lifetime recall history, including historical or superseded records.
STRUCTURE:BODY:ROOF AND PILLARS
Ford Motor Company (Ford) is recalling certain 2011-2019 Explorer vehicles. The A-pillar trim retention clips may not be properly engaged, allowing the trim to detach.
Consequence: A detached trim piece can fall off the vehicle, becoming a road hazard and increasing the risk of a crash.
Remedy: Dealers will inspect and replace the A-pillar trim as necessary, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model years. Owner notification letters were mailed between July 18, 2024 and December 16, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S02.
SUSPENSION:REAR
Ford Motor Company (Ford) is recalling certain 2011-2013 Explorer vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Mis…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain 2011-2013 Explorer vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. These vehicles may be equipped with a cross-axis ball joint (CABJ) replacement part that could seize, and result in a fracture of the outboard section of the rear suspension toe link.
Consequence: A rear toe link fracture can result in a loss of steering control, increasing the risk of a crash.
Remedy: Dealer will inspect for the presence of a CABJ. If a CABJ of any design is found, the dealer will inspect the tightness of the CABJ, and replace the CABJ, knuckle, and/or toe link as necessary, free of charge. Interim notification letters were mailed November 10, 2021. Owner notification letters were mailed on March 17, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S43.
SUSPENSION:REAR
Ford Motor Company (Ford) is recalling certain 2013-2017 Explorer vehicles originally sold, or ever registered, in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jerse…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain 2013-2017 Explorer vehicles originally sold, or ever registered, in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin, and the District of Columbia. Exposure to road salt can cause the cross-axis ball joint to corrode and seize, resulting in a fracture of the outboard section of the rear suspension toe link.
Consequence: A rear toe-link fracture can result in a loss of steering control, increasing the risk of a crash.
Remedy: Dealers will inspect and replace as necessary, the cross-axis ball joint (CABJ) knuckle, and replace the rear suspension toe links, free of charge. This recall is an expansion of previous NHTSA recall numbers 16V-245, 19V-435, and 20V-675. Certain vehicles previously repaired will need to return for the new remedy. An interim notification letter notifying owners of the safety risk were mailed on September 10, 2021. Owner notification letters were mailed on March 16, 2022. Owners may contact Ford's customer service at 1-866-436-7332. Ford's number for this recall is 21S32.
SUSPENSION:REAR
Ford Motor Company (Ford) is recalling certain 2013-2017 Explorer vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Miss…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain 2013-2017 Explorer vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin that were previously repaired under a prior recall numbers 16V-245 or 19V-435. The outboard section of a rear suspension toe link may fracture.
Consequence: A rear toe link fracture can result in a loss of steering control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will inspect the cross-axis ball joint (CABJ) knuckle attached to the rear suspension toe link and replace it as necessary, free of charge. The recall began November 27, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S62.
SUSPENSION:REAR
Ford Motor Company (Ford) is recalling certain 2011-2017 Explorer vehicles. The rear suspension toe links may fracture due to stress on the rear suspension.
Consequence: A fractured rear toe link will cause a sudden change in vehicle handling and increase the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the rear suspension toe links, and inspect both rear toe link ball joints, replacing the rear wheel knuckle(s), if necessary, free of charge. The recall began June 26, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S17.
SUSPENSION:REAR
Ford Motor Company (Ford) is recalling certain Wheel Hub Bearing assemblies, part number HB5Z-1104-C, incorrectly listed as being for installation on the rear axles of 2011-2017 Ford Explorer 4X2 vehicles. These bearings assemblies were manufactured without a…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain Wheel Hub Bearing assemblies, part number HB5Z-1104-C, incorrectly listed as being for installation on the rear axles of 2011-2017 Ford Explorer 4X2 vehicles. These bearings assemblies were manufactured without a self retention feature, possibly resulting in the separation of the wheel or wheel end.
Consequence: A loss of the wheel or wheel end can increase the risk of a crash.
Remedy: Ford will notify the distributors of the hubs specifying that they are to only be used on drive axles. It is believed that none of the hubs were purchased from Ford dealers for the incorrect application. Owners may contact Ford customer service at 1-866-436-7332.
FUEL SYSTEM, GASOLINE
Ford Motor Company (Ford) is recalling certain model year 2013 Explorer, Explorer Police Utility, Taurus, Taurus Police Interceptor, Flex, Lincoln MKS, and Lincoln MKT vehicles. In the affected vehicles, the fuel delivery module may crack, allowing fuel to le…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain model year 2013 Explorer, Explorer Police Utility, Taurus, Taurus Police Interceptor, Flex, Lincoln MKS, and Lincoln MKT vehicles. In the affected vehicles, the fuel delivery module may crack, allowing fuel to leak.
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel delivery module, free of charge. The recall began on December 21, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 13S04-S1.
STRUCTURE:BODY:DOOR
Ford Motor Company (Ford) is recalling certain model year 2011-2013 Explorer vehicles. In the affected vehicles, the interior door handle return spring may unseat, resulting in interior door handle that does not return to the fully stowed position after actua…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain model year 2011-2013 Explorer vehicles. In the affected vehicles, the interior door handle return spring may unseat, resulting in interior door handle that does not return to the fully stowed position after actuation.
Consequence: If the interior door handle return spring is unseated, the door may unlatch in the event of a side impact crash, increasing the risk of personal injury.
Remedy: Ford will notify owners, and dealers will inspect all four of the interior door handles and either repair or replace them, free of charge. The recall began on July 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S11.
STEERING:ELECTRIC POWER ASSIST SYSTEM
Ford Motor Company (Ford) is recalling certain model year 2011-2013 Ford Explorer vehicles manufactured May 17, 2010, through February 28, 2012. The affected vehicles may experience an intermittent connection in the electric power steering gear, which can cau…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain model year 2011-2013 Ford Explorer vehicles manufactured May 17, 2010, through February 28, 2012. The affected vehicles may experience an intermittent connection in the electric power steering gear, which can cause a loss of the motor position sensor signal resulting in a shut down of the power steering assist.
Consequence: If the vehicle experiences a loss of power steering assist it will require extra steering effort at lower speeds, increasing the risk of a vehicle crash.
Remedy: Ford will notify owners, and dealers will update the Power Steering Control Module (PSCM) software, free of charge. If a vehicle shows a history of a loss of motor position sensor signal when the vehicle is brought in for the recall remedy, its steering rack assembly will be replaced, free of charge. The recall began on July 23, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S06.
LATCHES/LOCKS/LINKAGES
Ford Motor Company (Ford) is recalling certain model year 2013 Ford Explorer, Taurus, and Lincoln MKS vehicles manufactured November 29, 2012, through December 12, 2012. In the affected vehicles, with sufficient door openings and closings, the child safety lo…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain model year 2013 Ford Explorer, Taurus, and Lincoln MKS vehicles manufactured November 29, 2012, through December 12, 2012. In the affected vehicles, with sufficient door openings and closings, the child safety locks may change from an activated position to a deactivated position without notice.
Consequence: If the child lock is deactivated, the door could be unlocked and opened from the inside which could lead to personal injury to an unrestrained child.
Remedy: Ford will notify owners, and dealers will test the safety locks. If necessary, the locks will be replaced free of charge. The recall began on August 2, 2013. Ford's recall number is 13S07. Owners may contact the Ford customer relationship center at 1-866-436-7332.
FUEL SYSTEM, GASOLINE
Ford is recalling certain model year 2013 Explorer, Taurus, Flex, Fusion, Police Interceptor Sedan and Police Interceptor Utility vehicles; and certain model year 2013 Lincoln MKS, MKT, and MKZ vehicles. In the affected vehicles, the fuel delivery module may …
Read the complete source summary
Ford is recalling certain model year 2013 Explorer, Taurus, Flex, Fusion, Police Interceptor Sedan and Police Interceptor Utility vehicles; and certain model year 2013 Lincoln MKS, MKT, and MKZ vehicles. In the affected vehicles, the fuel delivery module may develop a crack, allowing fuel to leak.
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel delivery module, free of charge. The recall began on July 20, 2013. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332. Ford's recall campaign number is 13S04.
FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY
Ford is recalling certain model year 2012 Taurus, Lincoln MKS, and model year 2013 Explorer vehicles manufactured July 19, 2011, through March 15, 2012. In the affected vehicles, the fuel tanks may have a marginally sealed seam in the side of the tank. As a …
Read the complete source summary
Ford is recalling certain model year 2012 Taurus, Lincoln MKS, and model year 2013 Explorer vehicles manufactured July 19, 2011, through March 15, 2012. In the affected vehicles, the fuel tanks may have a marginally sealed seam in the side of the tank. As a result, the fuel tanks may not provide the expected strength in the event of an impact. The tanks may also leak.
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will inspect the fuel tanks and replace them as necessary, free of charge. The recall began on May 9, 2013. Ford's recall campaign number is 13S03. Owners may contact Ford Motor Company Customer Relationship Center at 1-866-436-7332.
Reports Over Time
US complaints by filing month, latest 12 observed months.
25-12
26-01
26-02
26-03
26-04
26-05
26-06
26-07
26-08
26-09
26-10
26-11
A month with no bar is not evidence that no problems occurred. Publication and reporting delays affect totals.
Read chart data
2025-12
5
2026-01
5
2026-02
7
2026-03
15
2026-04
5
2026-05
5
2026-06
9
2026-07
4
2026-08
4
2026-09
4
2026-10
2
2026-11
2
RECHECK EVIDENCE LAB
The mileage lens
Where the available US complaint records fall by reported mileage.
Reported mileage at incident
Matched complaint records
Below 25,000 mi
199
25,000–49,999 mi
218
50,000–99,999 mi
596
100,000–149,999 mi
360
150,000+ mi
164
Missing or excluded mileage
702
1,537 of 2,239 matched complaints have positive, usable mileage. Source zero values can represent missing information and are excluded; values above 1.5 million miles are excluded. These are selected allegations with no vehicle-population denominator. The table cannot predict when your vehicle will fail. Mileage is retained in US source miles.
Crash flagged44US complaint allegations
Fire flagged11US complaint allegations
Towed flagged85US complaint allegations
Positive source flags are counted per deduplicated complaint, not verified incidents. Categories and flags can overlap; an unflagged or missing value does not prove an incident did not occur.
RECHECK EVIDENCE LAB
Your annual energy budget
Use official test estimates with your own distance and prices.
Scenario estimate, not a live price quote or total cost of ownership. Uses the selected source configuration’s combined test consumption. Weather, speed, battery condition, charging losses, taxes, maintenance, depreciation and insurance can change actual cost. Plug-in hybrids are excluded from this simple calculator because fuel and electricity use depend on charging behaviour. Your inputs stay in your browser.
2,239 deduplicated US complaint records. The most frequently named component categories are:
steering · 837 records
structure · 439 records
engine · 226 records
“Unknown or other” records are included in the total; they do not identify a component. Categories overlap. These are allegations, not confirmed defects or a failure rate.
Coverage boundary: US campaigns received since 2010; not a complete lifetime recall history Exact normalized make/model/year safety matches. Efficiency retains explicitly named source configurations; spelling/configuration differences may exclude records. US complaint counts do not establish Canadian experience or the probability of a defect.
Accident history, current mechanical condition, ownership, liens, individual recall applicability, repair completion and battery health are not established by this model-year report. No failure rate or reliability score is calculated from raw complaint totals.
Specifications & Efficiency
Official source configurations. No trim is assumed.
Source configuration
Fuel / powertrain
Combined efficiency
Range
Explorer FWD Automatic 6-spd
Regular Front-Wheel Drive
23 MPG
Data unavailable
Explorer AWD FFV Automatic (S6)
Gasoline or E85 All-Wheel Drive
19 MPG
Data unavailable
Explorer 2WD FFV Automatic (S6)
Gasoline or E85 Front-Wheel Drive
20 MPG
Data unavailable
Explorer FWD Automatic (S6)
Regular Front-Wheel Drive
20 MPG
Data unavailable
Explorer AWD Automatic (S6)
Regular All-Wheel Drive
18 MPG
Data unavailable
Explorer AWD Automatic (S6)
Regular All-Wheel Drive
19 MPG
Data unavailable
Official test estimates vary with configuration, driving and weather. Fuel codes are retained as published; US and Canadian test measures are shown in their source units. Plug-in hybrid source ranges and operating modes are shown separately; they are not added together.
More from the official configuration records
Figures belong to each source configuration. Test conditions and charging assumptions apply; tailpipe emissions exclude fuel and electricity production. No missing specifications are inferred.
US official records; applicability in Canada is not established.
24 matched manufacturer communications · 6 matched investigations. Communications are not necessarily recalls or technical service bulletins.
EA15005 · Front Brake Hose Failure
On April 29, 2015, the Office of Defects Investigation (ODI) opened PE15-017 to investigate a report alleging incidents of front brake hose failure in model year (MY) 2015 Ford Explorer Police Interceptor vehicles used by the Sacramento Police Department in its pursuit driving training program (VOQ 10705832).On September 28, 2015, ODI upgraded the investigation to an Engineering Analysis (EA15-005) to assess maximum front caliper crimp temperatures under various test conditions, test hose assemblies removed from police interceptor service for any signs of thermal degradation, and further assess field data for evidence of a defect trend related to the alleged defect.The alleged defect results from exposure to extremely high heat at the caliper-side hose crimp. NHTSA?s vehicle testing suggests that the conditions necessary to produce the critical temperatures in the subject components result from drive-soak intervals that can occur during the Sacramento training program.NHTSA's testing of hose assemblies returned from police interceptor service did not identify any evidence of thermal degradation.NHTSA has not confirmed any incidents of caliper crimp failures due to overheating in vehicles not subjected to the Sacramento training course driving.The low number of hose assembly failure reports and the absence of any verified incidents of heat related front brake hose crimp failures since 2015 suggests that the Sacramento PD incidents resulted from conditions unique to the training program.A safety related defect trend has not been identified at this time and further use of Agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The Agency will take further action if warranted by the circumstances.For additional information, see the Closing Report in the document file for EA15-005 on www.nhtsa.gov.
During the EA17-002 investigation, the agency reviewed and analyzed reports of exhaust odors in the passenger cabins of Model Year 2011 to 2017 Ford Explorers. This investigation required an approach that incorporated knowledge and expertise from the automotive, medical, environmental health, and occupational safety fields. The agency conducted an in-depth investigation that encompassed the review of over 6,500 consumer complaints, conducting field inspections, and testing the relevant vehicles, both independently and in coordination with Ford and other entities. During the investigation, the evolution of Ford service bulletins intended to reduce the level of exhaust odors and carbon monoxide (CO) entering the occupant compartment was examined and independent tests to evaluate the effectiveness of the final Field Service Actions (FSA) for both consumer and police vehicles were conducted. As part of the investigation, the agency also examined the effects of cracked exhaust mani-cats on the measured CO levels in the vehicles and tested the FSA repairs to ensure they did not adversely impact occupant compartment CO levels due to cracked mani-cats.The investigation identified upfitting issues for Police Interceptor vehicles. Upfitting (sirens, lights, cages, auxiliary power, etc.) is typically performed by governmental fleet operations, independent repair facilities, or local Ford dealers after the sale of the new vehicle. Sealing issues caused by upfitting were responsible for the highest measured carbon monoxide levels in tested vehicles. The police FSA instructs how to inspect the quality of the vehicle upfits and how to properly seal any leaks caused by these upfits, at no cost to the police agency. Similarly, the highest CO levels measured in consumer vehicles were usually traced to sealing issues caused by rear crash damage where the repairs did not ensure sealing integrity. The most recent Ford FSA procedure for both the police (17B25) and consumer vehicles (17N03) includes an HVAC reprogramming operation. Tests by Ford and NHTSA have demonstrated a substantial reduction of CO levels due solely to the HVAC reprogramming. Other FSA repairs also demonstrated measurable contributions to CO level reductions during controlled tests.Throughout the investigation, vehicles accurately measured with higher levels of carbon monoxide were almost always affected by upfitter alterations, damage, or other causes compromising rear passenger cabin seals.NHTSA received thousands of reports alleging odors which triggered a variety of physiological responses, predominately nausea, headaches, and lightheadedness. NHTSA focused the investigation on accurately measuring vehicle CO levels, and accurately measuring carboxyhemoglobin (COHB) levels from properly administered blood tests. Using rigorous test methods to produce exhaust gas intrusion in vehicles with a properly performed FSA, occupant compartment CO levels remained below current environmental limits for CO in any environment (EPA ambient air quality standards). Furthermore, even without FSA repairs, no vehicles unaffected by upfitter issues or prior crash damage were identified with CO levels that exceed accepted occupational CO exposure levels. This investigation finds that the 2011-2017 Ford Explorer vehicles when accurately measured produce occupant compartment CO levels which fall below current accepted health standards, and could not identify COHB levels for vehicle drivers or other occupants, which exceeded thresholds for acute physiological effects. Therefore, the agency has not identified a defect that represents an unreasonable risk to motor vehicle safety.This inve
On May 27, 2014 and amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist in approximately 179,027 model year (MY) 2011 through 2013 Ford Explorer vehicles equipped with electric power assisted steering (EPAS), including 82,328 MY 2011 Explorersthat are the subject of PE12-017.Ford has assigned the recall number 14S06.The NHTSA recall number is 14V-286.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Sudden loss of power steering assist while driving can occur in the subject vehicles if the system loses electrical power or whenever the system detects a fault that requires it to enter fail-safe mode, which removes power from the EPAS motor and defaults to manual steering.Ford's DIR indicates that the majority of steering assist failures in the recalled vehicles have been caused by an intermittent electrical connection in the Power Steering Control Module (PSCM) that can lead to a loss of the motor position sensor signal.Ford's remedy instructs dealers to check the PSCM for diagnostic trouble codes (DTC).If upon initial inspection a loss of steering assist DTC is present, dealers will replace the steering gear at no charge to the owner and update the PSCM with revised software.Following detection of a motor position sensor signal fault, the revised software will provide audible and visual warnings to the driver that a power steering system fault has been detected and will maintain steering assist for the remainder of that drive cycle.If no DTC is present, dealers will reprogram the PSCM with the revised software. Analysis of information from all sources identified a total of 969 complaints and 4,059 warranty claims related to loss of power steering assist while driving in the MY 2011 through 2012 Explorer vehicles, resulting in a complaint rate of 5.4 incidents per thousand vehicles and a warranty claim rate of 2.3 percent.ODI identified 15 crashes with evidence indicating loss of power steering assist may have been a factor.All 15 crashes involved low-speed impacts with roadside objects during turning maneuvers, resulting in minor vehicle damage or no damage.In one incident that occurred in a low-speed curve, the driver attempted to brake in response to the sudden increase in steering effort and inadvertently applied the accelerator pedal instead.This caused the vehicle to run off the side of the road and strike a wooden pole at approximately 15 mph.Another incident occurred when the driver was unable to to negotiate a left-turn at an intersection and ran off the road into a shallow ditch, resulting in moderate front-end damage to the vehicle and minor injuries to the driver that did not require medical treatment. This investigation is closed.All ODI complaints associated with this closing resume are listed in the Attachment 1.
The Office of Defects Investigation (ODI) opened PE14-027 based on a report of 13 front brake hose (jounce hose) failures in 11 vehicles in the District of Columbia Metropolitan Police Department (DCMPD) fleet of 46 model year (MY) 2013 Ford Explorer Police Interceptor (PI) vehicles (VOQ 10621634).The DCMPD fleet provided Ford with 71 jounce hoses for analysis, including 4 of the 13 failed hoses.Inspection of each of the failed hoses identified a small tear in the outer cover on the body end of the hoses on the outboard side. Ford?s lab analysis of these hoses identified splits in the inner liners 1.5-2.0mm from the end of the nipple (outside of the crimped ferrule joint).Ford conducted pressure testing of 10 randomly selected samples of the remaining 67 hoses that had not experienced leaks and 9 of the samples leaked at 6,000 psi.Ford?s examination of the 9 hoses that leaked in the pressure tests found 4 that failed on the outboard side of the hose (similar to the 4 leaking field parts) and 5 that failed on the body end of the hose on the inboard side.Four additional non-leaking hoses were sent to the hose supplier, Hitachi, for analysis.Broken yarn was observed in scanning electron microscope examinations at both the body side and caliper side hose to ferrule crimps, indicating severe bending stress had occurred at these locations. Hitachi supplied an additional set of non-leaking field return hoses and a brand new set of hoses to an outside laboratory (Element Materials Technology) for analysis.The lab did not identify any manufacturing or material deficiencies in the hoses and concluded that the hose failures were caused by excessive bending stresses.Based on the examinations of the returned jounce hoses, Ford conducted durability testing on new hoses that were the same design as those found on the subject vehicles.Ford first determined the worst case conditions for the hoses; jounce bumpers removed, internal rebound stops fully compressed, and shock absorbers attached. With the jounce hose installed, the steering was rotated to the maximum turn angle while the suspension was translated from full jounce to full rebound.This determined the maximum hose length of 13.0in (331mm) and a minimum hose bending radius of 1.6in (40mm).Using these conditions hoses tested on a Suspension Motion Simulator far surpassed Ford?s performance specifications. Twenty (20) complaints of front brake jounce hose failure were identified on a total of 18 Explorer PI vehicles, including the 13 hose failures in 11 vehicles from the DCMPD fleet that prompted PE14-027.The remaining 7 complaints included 3 from one fleet that reportedly occurred on the banjo block end of the hose assembly and single complaints from 4 other fleets.Only two brake hose assemblies were used in the subject and peer Explorer vehicles, with the BB53 level hose used until June 20, 2012, and an updated DB53 level hose used thereafter.No pattern of failures was observed by hose assembly, with 15 of failures involving the BB53 hose assembly (including the 13 from DCMPD manufactured in March 2012) and 5 the DB53 hose assembly built after June 20, 2012. No root cause was determined for the reported Explorer PI jounce hose failures, but Ford identified improper service repair procedures (e.g., hanging the brake caliper from the brake hose during brake pad replacement) as a possible contributor to higher than expected rate of front brake jounce hose leaks. ODI?s analysis of field data, hose inspection and test data did not identify evidence of any defects in hose material, manufacture or vehicle installation.The closing of this invest
Showing up to 8 communication summaries and 4 investigations. Export coverage: communications received 2020–2026 only. Canadian applicability is not inferred. Consult NHTSA for full records.
Before You Buy
Questions to take to a seller or qualified mechanic.
Verify the VIN and ask the manufacturer to confirm applicability and completion of recall repairs.
Ask for documentation related to the official STRUCTURE:BODY:ROOF AND PILLARS campaign (24V031000).
Ask for documentation related to the official SUSPENSION:REAR campaign (21V746000).
Ask a mechanic to investigate any symptoms associated with reported categories; complaints alone are not a diagnosis.
Review service records and arrange an independent pre-purchase inspection.
A research brief for the 2013 Ford Explorer, built from this report.
Record the VIN, market and exact powertrain. Confirm open recalls and completed remedies with the manufacturer.
Ask for repair documentation for campaign 24V031000 (STRUCTURE:BODY:ROOF AND PILLARS). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 21V746000 (SUSPENSION:REAR). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 21V537000 (SUSPENSION:REAR). A model-year match does not establish that this VIN is affected.
steering: 837 matched US complaint records mention this category. Ask the seller about related symptoms, prior diagnosis and documented repairs; ask an independent mechanic which checks fit this exact configuration.
structure: 439 matched US complaint records mention this category. Ask the seller about related symptoms, prior diagnosis and documented repairs; ask an independent mechanic which checks fit this exact configuration.
unknown or other: 345 matched US complaint records mention this category. Ask the seller about related symptoms, prior diagnosis and documented repairs; ask an independent mechanic which checks fit this exact configuration.
Compare service records with the manufacturer’s schedule and arrange an independent pre-purchase inspection. This checklist is not a diagnosis or an expert inspection.