Open this section to check available listings. No listing request is made until you open it.
Source: Car Handshake and participating dealerships. Year, make and model must match to appear here; trims and specifications can differ. Listings do not establish vehicle condition or recall repair status.
Canadian owner complaints
Coverage, without substituted US totals.
Canadian complaint totals are not available in Recheck’s current dataset. This does not mean there are no complaints.
Canadian recalls come from Transport Canada and efficiency ratings from NRCan. US complaints and bulletins are optional context below; they do not establish Canadian applicability.
Canadian archive snapshot, including historical or superseded records.
Lights And Instruments
Issue:
On certain vehicles, the instrument panel cluster could stop working. As a result, warnings, tell-tales and gauges may not display.
Note: This recall only affects vehicles equipped with a 3.5" instrument cluster panel.
Safety Risk:
Warnings, tell-…
Read the complete source summary
Issue:
On certain vehicles, the instrument panel cluster could stop working. As a result, warnings, tell-tales and gauges may not display.
Note: This recall only affects vehicles equipped with a 3.5" instrument cluster panel.
Safety Risk:
Warnings, tell-tales and gauges that don't display could increase the risk of a crash.
Corrective Actions:
FCA Canada will notify owners by mail and advise you to take your vehicle to a dealership to replace the instrument panel cluster.
Issue:
Under certain conditions, the clutch pressure plate could overheat and break. If this happens, the pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle.
Note: This recall only affects certain …
Read the complete source summary
Issue:
Under certain conditions, the clutch pressure plate could overheat and break. If this happens, the pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle.
Note: This recall only affects certain vehicles equipped with a 3.6 L engine and a manual transmission. Vehicles repaired under FCA Canada recalls Y01, Y03 and Y07 (Transport Canada recall 2021-035) also require this repair.
Safety Risk:
Debris from an overheated and fractured pressure plate could contact nearby parts and increase the risk of a fire. Parts that fall from the vehicle could create a road hazard for others and increase the risk of injury.
Corrective Actions:
FCA Canada will notify owners by mail and advise you to tale your vehicle to a dealership to replace the clutch assembly. The dealer will also inspect and, if necessary, update the instrument panel cluster and powertrain control module software.
Issue:
In certain circumstances, the clutch pressure plate could overheat and break. If this happens, the pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle.
Note: This recall only affects certain v…
Read the complete source summary
Issue:
In certain circumstances, the clutch pressure plate could overheat and break. If this happens, the pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle.
Note: This recall only affects certain vehicles equipped with a 3.6 L engine and a manual transmission.
Safety Risk:
Debris from an overheated and fractured pressure plate could contact nearby parts and increase the risk of a fire. Parts that fall from the vehicle could create a road hazard for others, and increase the risk of injury.
Corrective Actions:
FCA Canada will notify owners by mail and instruct you to take your vehicle to a dealer to update vehicle software. This update will reduce the engine power if the clutch overheats.
Issue:
On certain vehicles equipped with a manual transmission, the clutch pressure plate could overheat and break. If this happens, there would be a loss of power to the wheels. A broken pressure plate may also crack or break the transmission case. This coul…
Read the complete source summary
Issue:
On certain vehicles equipped with a manual transmission, the clutch pressure plate could overheat and break. If this happens, there would be a loss of power to the wheels. A broken pressure plate may also crack or break the transmission case. This could cause debris to fall from the vehicle.
Safety Risk:
A sudden of loss power to the wheels could increase the risk of a crash. Additionally, debris from an overheated and fractured pressure plate could contact nearby parts and increase the risk of a fire. Parts that fall from the vehicle could create a road hazard for others, and increase the risk of injury.
Corrective Actions:
FCA Canada will notify owners by mail and instruct you to take your vehicle to a dealer to inspect the clutch system, install a protective hose sleeve, reroute a wire harness, and replace components as necessary
Certain vehicles may have been built with an improperly welded front track bar bracket. This could result in the bracket separating from the frame, which would reduce steering response and increase the risk of a crash causing injury and/or damage to property. …
Read the complete source summary
Certain vehicles may have been built with an improperly welded front track bar bracket. This could result in the bracket separating from the frame, which would reduce steering response and increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and repair the front track bar bracket welds as necessary. Note: Prior to complete separation of the bracket from the frame, a driver may notice a front end noise, an off-center steering wheel position, a “Service Electronic Stability Control” message and/or Electronic Stability control light on in the instrument cluster.
Certain vehicles may have been built with a defective powertrain controller. If the powertrain controller fails while driving the engine may stall, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the po…
Read the complete source summary
Certain vehicles may have been built with a defective powertrain controller. If the powertrain controller fails while driving the engine may stall, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will replace the powertrain controller.
On certain vehicles, the steering intermediate shaft may not have been properly manufactured. If the shaft were to fail, the steering response could be reduced, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will i…
Read the complete source summary
On certain vehicles, the steering intermediate shaft may not have been properly manufactured. If the shaft were to fail, the steering response could be reduced, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect and replace the steering intermediate shaft as necessary.
On certain vehicles, an electronic fault may create a situation where the cruise control cannot be deactivated. If this occurs and the driver does not apply the brakes or shift the transmission to neutral, the vehicle could maintain speed or accelerate without…
Read the complete source summary
On certain vehicles, an electronic fault may create a situation where the cruise control cannot be deactivated. If this occurs and the driver does not apply the brakes or shift the transmission to neutral, the vehicle could maintain speed or accelerate without warning, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will inspect the Powertrain Control Module (PCM) software and perform an update as necessary. Note: In the interim, owners are advised not to use the cruise control until the vehicle is repaired.
Certain vehicles may have been built with reduced corrosion protection on the left rear under body ladder rail. This could cause the affected area to corrode prematurely, which could result in the left rear seat mount to become loose or reduce the strength of …
Read the complete source summary
Certain vehicles may have been built with reduced corrosion protection on the left rear under body ladder rail. This could cause the affected area to corrode prematurely, which could result in the left rear seat mount to become loose or reduce the strength of the rear floor pan, increasing the risk of injury to the seat occupants in the event of a crash. Correction: Dealers will inspect the under body ladder rail and apply rust protection, or if deemed unrepairable, FCA will review further.
Model-year recalls do not establish repair completion.
Confirm open recalls with the manufacturer and ask a dealer whether the repairs are complete. Recheck’s VIN decoder identifies the vehicle; it does not provide recall repair status.
Use official test estimates with your own distance and prices.
Scenario estimate, not a live price quote or total cost of ownership. Uses the selected source configuration’s combined test consumption. Weather, speed, battery condition, charging losses, taxes, maintenance, depreciation and insurance can change actual cost. Plug-in hybrids are excluded from this simple calculator because fuel and electricity use depend on charging behaviour. Your inputs stay in your browser.
Coverage boundary: Canadian archive snapshot Exact normalized make/model/year safety matches. Efficiency retains explicitly named source configurations; spelling/configuration differences may exclude records. US complaint counts do not establish Canadian experience or the probability of a defect.
Accident history, current mechanical condition, ownership, liens, individual recall applicability, repair completion and battery health are not established by this model-year report. No failure rate or reliability score is calculated from raw complaint totals.
Specifications & Efficiency
Official source configurations. No trim is assumed.
Source configuration
Fuel / powertrain
Combined efficiency
Range
Wrangler JK 4X4 A5
X 3.6 L engine
12.8 L/100 km
Data unavailable
Wrangler JK 4X4 M6
X 3.6 L engine
12.8 L/100 km
Data unavailable
Wrangler JK Unlimited 4X4 A5
X 3.6 L engine
13.4 L/100 km
Data unavailable
Wrangler JK Unlimited 4X4 M6
X 3.6 L engine
13.3 L/100 km
Data unavailable
Official test estimates vary with configuration, driving and weather. Fuel codes are retained as published; US and Canadian test measures are shown in their source units. Plug-in hybrid source ranges and operating modes are shown separately; they are not added together.
More from the official configuration records
Figures belong to each source configuration. Test conditions and charging assumptions apply; tailpipe emissions exclude fuel and electricity production. No missing specifications are inferred.
Wrangler JK 4X4 · A5 — source specification details
Vehicle class
Sport utility vehicle: Small
Engine displacement
3.6 L
Cylinders
6
City fuel consumption
14.1 L/100 km
Highway fuel consumption
11.1 L/100 km
Tailpipe CO₂ emissions
299 g/km
Wrangler JK 4X4 · M6 — source specification details
Vehicle class
Sport utility vehicle: Small
Engine displacement
3.6 L
Cylinders
6
City fuel consumption
14.2 L/100 km
Highway fuel consumption
11.0 L/100 km
Tailpipe CO₂ emissions
298 g/km
Wrangler JK Unlimited 4X4 · A5 — source specification details
Vehicle class
Sport utility vehicle: Small
Engine displacement
3.6 L
Cylinders
6
City fuel consumption
14.7 L/100 km
Highway fuel consumption
11.7 L/100 km
Tailpipe CO₂ emissions
313 g/km
Wrangler JK Unlimited 4X4 · M6 — source specification details
Vehicle class
Sport utility vehicle: Small
Engine displacement
3.6 L
Cylinders
6
City fuel consumption
15.0 L/100 km
Highway fuel consumption
11.4 L/100 km
Tailpipe CO₂ emissions
312 g/km
Canadian defect investigations
Check the current official Transport Canada register.
Canadian investigation records are not imported into this report. Check the official register for affected vehicles, investigation details and current status; no match or status is implied here.
A research brief for the 2018 Jeep Wrangler, built from this report.
Record the VIN, market and exact powertrain. Confirm open recalls and completed remedies with the manufacturer.
Ask for repair documentation for campaign 2024504 (Lights And Instruments). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 2023089 (Powertrain). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 2021035 (Powertrain). A model-year match does not establish that this VIN is affected.
Compare service records with the manufacturer’s schedule and arrange an independent pre-purchase inspection. This checklist is not a diagnosis or an expert inspection.
Optional US contextNHTSA complaints, communications and investigations · not Canadian records
These are US records. Models, equipment, campaigns and driving conditions can differ. Counts are not Canadian complaint totals, verified reviews or reliability ratings.
Reported Problem Categories
US NHTSA complaints for the 2018 Jeep Wrangler.
STEERING
1117
SUSPENSION
343
ELECTRICAL SYSTEM
269
UNKNOWN OR OTHER
212
POWER TRAIN
178
US context, not Canadian complaint counts. NHTSA documents known discrepancies in its bulk complaint file. Consumer allegations are not confirmed defects. One complaint can mention several categories. Counts are not failure rates.
Reports Over Time
US complaints by filing month, latest 12 observed months.
25-12
26-01
26-02
26-03
26-04
26-05
26-06
26-07
26-08
26-09
26-10
26-11
A month with no bar is not evidence that no problems occurred. Publication and reporting delays affect totals.
Read chart data
2025-12
7
2026-01
11
2026-02
9
2026-03
2
2026-04
13
2026-05
10
2026-06
6
2026-07
6
2026-08
18
2026-09
11
2026-10
4
2026-11
3
RECHECK EVIDENCE LAB
The mileage lens
Where the available US complaint records fall by reported mileage.
Reported mileage at incident
Matched complaint records
Below 25,000 mi
1,010
25,000–49,999 mi
121
50,000–99,999 mi
57
100,000–149,999 mi
12
150,000+ mi
1
Missing or excluded mileage
629
1,201 of 1,830 matched complaints have positive, usable mileage. Source zero values can represent missing information and are excluded; values above 1.5 million miles are excluded. These are selected allegations with no vehicle-population denominator. The table cannot predict when your vehicle will fail. Mileage is retained in US source miles.
Crash flagged22US complaint allegations
Fire flagged26US complaint allegations
Towed flagged40US complaint allegations
Positive source flags are counted per deduplicated complaint, not verified incidents. Categories and flags can overlap; an unflagged or missing value does not prove an incident did not occur.
Bulletins & Investigations
US official records; applicability in Canada is not established.
667 matched manufacturer communications · 5 matched investigations. Communications are not necessarily recalls or technical service bulletins.
DP18004 · Frame Weld Deficiencies
In a letter received on October 24, 2018, a citizen petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) opened a Defect Petition (DP18-004) to evaluate whether to grant or deny the petition. On March 8, 2019, ODI sent an Information Request letter to Fiat Chrysler Automobiles (FCA) requesting information on frame weld related issues on all MY 2018-2019 Jeep Wrangler 'JL' vehicles. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (NHTSA Recall No. 18V-675), ODI opted to include a request for additional information concerning reports of steering shimmy or wobble, loose steering, and steering lockup in the March request letter. ODI has performed a preliminary analysis on the information obtained from FCA. Based on ODI's review of the applicable materials, NHTSA has decided to grant the petition. While reviewing the applicable materials obtained from the manufacturer, ODI identified various reports and references to frame welded component detachments that were outside of the scope of NHTSA Recall No. 18V-675. Additionally, the information that FCA provided did not adequately address whether frame weld quality deficiencies compromise the structural integrity of vehicles, and therefore may pose an unreasonable risk to motor vehicle safety. Finally, ODI needs to further evaluate the alleged steering-related defects reported through MY 2019 and the alleged defects' relation to weld quality.The petition was granted on September 16, 2019. Preliminary Evaluation PE19-012 has been opened to further assess the scope, frequency, and potential safety-related consequences of alleged weld quality deficiencies and steering related concerns on the MY 2018-2019 'JL' Jeep Wrangler vehicles.The ODI reports cited above can be viewed on NHTSA.gov under the following reference numbers:11234967, 11222390, 11219370, 11217080, 1204905, 11179954, 11171786, 11161243, 11155523, 11153044, 11143617, 11142722, 11142426, 11141336, 11141035, 11140637, 11140344, 11140262, 11140085, 11140057, 11139880, 11139866, 11139557, 11139467, 11139436, 11138974, 11138758, 11138757, 11132030, 11129738, 11129667, 11124312, 11120232, 11119676, 11119650, 11119454, 11119450, 11115658, 11115137, 11113029, 11112515, 11110583, 11109903, 11093172, 11088501, 11076098
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
On July 17, 2019, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 19-008 after receiving three Vehicle Owner Questionnaire (VOQ) reports alleging the driver's side seat belt buckle separated from the seat frame, rendering the seat belt non-functional. The VOQs involved model year (MY) 2015 and 2016 Jeep Wrangler (JK platform) that were configured for right-hand drive (RHD) use. On August 8, 2019, ODI issued an information request (IR) letter to FCA.The scope of the IR included all JK Wrangler produced for sale in the U.S. (both left- and right-hand drive), and amongst other things, requested any reports or allegations of driver's seat belt bracket failures on these vehicles. In its review of FCA's response, ODI determined that approximately 1.7 million JK Wrangler were produced from MY 2007 to 2018, about 16,000 of which were configured for RHD. ODI notes that the RHD Wrangler are typically used for rural postal delivery which often experience a more severe duty cycle. Also RHD JK was was not produced in MY 2007.As explained in the IR response, FCA identified three distinct populations of JK Wrangler concerning the driver's seat belt bucket bracket; specifically the MY 2007-2018 LHD (~1.7M units), the MY 2008-2010 RHD (4,563 units), and the MY 2011-2018 RHD (11,463 units) populations.FCA provided details on the designs used in each of these populations, identifying specific differences deemed pertinent to the strength and durability of each unique bracket design. FCA further reviewed its analysis of the complaint and warranty data identified under the IR, and noting that it had not identified any allegations of bracket failures on the LHD population, and only one allegation on the MY 2008-2010 RHD vehicles. By comparison, FCA identified 24 allegations of bracket failure for the MY 2011-2018 RHD JK, including two reports duplicative of the VOQs. Neither the FCA nor the VOQ reports allege an injury or fatality due to bracket failure. Based on this analysis, FCA decided to conduct a safety recall for the MY 2011-2018 RHD JK population. On September 30, 2019, FCA submitted a Defect Information Report initiating NHTSA Safety Recall 19V-680 (FCA No. VA6). Under the recall action, FCA will replace the driver's seat belt bracket on MY 2011-2018 RHD Jeep JK Wrangler. The repair will be conducted free of charge.In view of FCA's recall action, and its explanations of the scope of that action, ODI is closing PE19-008. ODI will continue to monitor the non-recalled RHD, and the LHD JK Wrangler for evidence of seat belt bracket failure and will take further action if warranted.The three VOQ reports cited above can be reviewed at NHTSA.gov under the following reference numbers:11190251, 11218472, 11231639.
Showing up to 8 communication summaries and 4 investigations. Export coverage: communications received 2020–2026 only. Canadian applicability is not inferred. Consult NHTSA for full records.
Sources & Last Updated
Trace the evidence behind this report.
Transport Canada Vehicle Recalls Database · Original source · Evidence updated Nov 17, 2026
US NHTSA complaints · optional US context only · Original source · Retrieved Nov 17, 2026 · Counts deduplicated by ODI number.