Open this section to check available listings. No listing request is made until you open it.
Source: Car Handshake and participating dealerships. Year, make and model must match to appear here; trims and specifications can differ. Listings do not establish vehicle condition or recall repair status.
Reported Problem Categories
US NHTSA complaints for the 2006 Ford Crown Victoria.
STEERING
27
VEHICLE SPEED CONTROL
9
AIR BAGS
7
ELECTRICAL SYSTEM
4
SUSPENSION
4
NHTSA documents known discrepancies in its bulk complaint file. Consumer allegations are not confirmed defects. One complaint can mention several categories. Counts are not failure rates.
At a Glance
Source configurations, without assumed specifications.
US campaigns received since 2010; not a complete lifetime recall history, including historical or superseded records.
STEERING:RACK AND PINION:PINION SHAFT
Ford Motor Company (Ford) is recalling certain model year 2005-2011 Ford Crown Victoria, 2005-2011 Mercury Grand Marquis vehicles manufactured March 23, 2004, to August 30, 2011, and 2005-2011 Lincoln Town Car vehicles manufactured March 8, 2004, to August 30,…
Read the complete source summary
Ford Motor Company (Ford) is recalling certain model year 2005-2011 Ford Crown Victoria, 2005-2011 Mercury Grand Marquis vehicles manufactured March 23, 2004, to August 30, 2011, and 2005-2011 Lincoln Town Car vehicles manufactured March 8, 2004, to August 30, 2011, and on which the upper intermediate shaft was serviced during the course of safety recall 13V-385. The prior repairs may not have been correctly performed.
Consequence: Improper servicing of the upper intermediate shaft could cause the shaft to separate, which can then result in a loss of steering control, and increasing the risk of a crash.
Remedy: Ford will notify the owners of vehicles whose repair records reflect that the upper intermediate steering shaft was repaired during the course of the prior recall 13V-385. Dealers will inspect and replace the upper immediate shaft if necessary free of charge. The recall began November 17, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S25.
STEERING
Ford is recalling certain model year 2005-2011 Ford Crown Victoria (including Crown Victoria Police Interceptors), Mercury Grand Marquis, and Lincoln Town Car vehicles. The affected vehicles are currently registered or were originally sold in Connecticut, Dela…
Read the complete source summary
Ford is recalling certain model year 2005-2011 Ford Crown Victoria (including Crown Victoria Police Interceptors), Mercury Grand Marquis, and Lincoln Town Car vehicles. The affected vehicles are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. Severe corrosion can seize the lower intermediate shaft which may cause the upper intermediate shaft to collapse and the steering column lower bearing to separate.
Consequence: If the lower bearing separates, the vehicle may experience a loss of steering, increasing the risk of a crash.
Remedy: Ford will notify owners and dealers will replace the lower intermediate shaft, free of charge. The upper intermediate shaft and steering column lower bearing will be inspected to identify any damage that may have occurred as a result of lower intermediate shaft corrosion, and repaired or replaced as necessary. If the steering column lower bearing has separated, a retainer clip will be installed. The recall began on October 23, 2013. Owners may contact Ford at 1-866-436-7332. Ford's recall number is 13S08.
Reports Over Time
US complaints by filing month, latest 12 observed months.
18-07
18-08
19-03
19-07
19-09
19-11
20-07
20-11
21-02
23-04
23-08
26-07
A month with no bar is not evidence that no problems occurred. Publication and reporting delays affect totals.
Read chart data
2018-07
1
2018-08
1
2019-03
1
2019-07
1
2019-09
1
2019-11
1
2020-07
1
2020-11
1
2021-02
1
2023-04
1
2023-08
1
2026-07
1
RECHECK EVIDENCE LAB
The mileage lens
Where the available US complaint records fall by reported mileage.
Reported mileage at incident
Matched complaint records
Below 25,000 mi
6
25,000–49,999 mi
3
50,000–99,999 mi
11
100,000–149,999 mi
18
150,000+ mi
10
Missing or excluded mileage
5
48 of 53 matched complaints have positive, usable mileage. Source zero values can represent missing information and are excluded; values above 1.5 million miles are excluded. These are selected allegations with no vehicle-population denominator. The table cannot predict when your vehicle will fail. Mileage is retained in US source miles.
Crash flagged10US complaint allegations
Fire flagged0US complaint allegations
Towed flagged5US complaint allegations
Positive source flags are counted per deduplicated complaint, not verified incidents. Categories and flags can overlap; an unflagged or missing value does not prove an incident did not occur.
RECHECK EVIDENCE LAB
Your annual energy budget
Use official test estimates with your own distance and prices.
Scenario estimate, not a live price quote or total cost of ownership. Uses the selected source configuration’s combined test consumption. Weather, speed, battery condition, charging losses, taxes, maintenance, depreciation and insurance can change actual cost. Plug-in hybrids are excluded from this simple calculator because fuel and electricity use depend on charging behaviour. Your inputs stay in your browser.
Coverage boundary: US campaigns received since 2010; not a complete lifetime recall history Exact normalized make/model/year safety matches. Efficiency retains explicitly named source configurations; spelling/configuration differences may exclude records. US complaint counts do not establish Canadian experience or the probability of a defect.
Accident history, current mechanical condition, ownership, liens, individual recall applicability, repair completion and battery health are not established by this model-year report. No failure rate or reliability score is calculated from raw complaint totals.
Specifications & Efficiency
Official source configurations. No trim is assumed.
Source configuration
Fuel / powertrain
Combined efficiency
Range
Crown Victoria Automatic 4-spd
Regular Rear-Wheel Drive
18 MPG
Data unavailable
Crown Victoria Automatic 4-spd
Gasoline or E85 Rear-Wheel Drive
18 MPG
Data unavailable
Crown Victoria Police Automatic 4-spd
Regular Rear-Wheel Drive
17 MPG
Data unavailable
Official test estimates vary with configuration, driving and weather. Fuel codes are retained as published; US and Canadian test measures are shown in their source units. Plug-in hybrid source ranges and operating modes are shown separately; they are not added together.
More from the official configuration records
Figures belong to each source configuration. Test conditions and charging assumptions apply; tailpipe emissions exclude fuel and electricity production. No missing specifications are inferred.
US official records; applicability in Canada is not established.
2 matched manufacturer communications · 3 matched investigations. Communications are not necessarily recalls or technical service bulletins.
EA13004 · Loss of Steering Control
In its recall notice dated August 26, 2013, Ford Motor Company (Ford) notified NHTSA of a safety defect condition that may result in loss of steering in approximately 355,000 model year (MY) 2005 through 2011 Ford Crown Victoria and Mercury Grand Marquis vehicles built at the St. Thomas Assembly Plant, MY 2005 through 2007 Lincoln Town Car vehicles built at the Wixom Assembly Plant, and certain MY 2008 through 2011 Lincoln Town Car vehicles built at the St. Thomas Assembly Plant and that are currently registered or were originally sold in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin (NHTSA Recall 13V-385, Ford Recall 13S08).Ford's recall addresses a corrosion related defect in the lower intermediate shaft that may result in separation of the steering column lower bearing and loss of steering control.Ford's recall will remedy the defect condition by instructing dealers to replace the lower intermediate shaft and to inspect and repair the upper intermediate shaft and steering column lower bearing as necessary.A retaining clip will be installed if the lower bearing has separated.Ford's investigation of steering column separations in the subject vehicles identified a defect condition in the lower intermediate shaft that could result in separation of the column lower bearing.According to Ford's August 26th defect report, severe corrosion of the lower intermediate shaft may cause the lower intermediate shaft swing link joint(s) to stiffen or seize.Ford determined that forces acting on the upper intermediate shaft because of seized swing links may eventually cause the upper intermediate shaft to collapse, which may result in separation of the column lower bearing and loss of steering control.Analysis of ODI complaints and Ford complaints and warranty identified 22 incidents of steering separation (12 complaints and 10 non-duplicative warranty claims) that may be related to the lower intermediate shaft defect condition.All 22 incidents involved vehicles in the recall region, where 419,210 or roughly half (52%), of the subject vehicles were sold.Ford's investigation also determined that column lower bearing separation may occur in vehicles that experienced upper intermediate shaft collapse in prior frontal impact collisions if the shaft was not properly diagnosed and repaired.Ford identified 13 steering separation incidents outside the recall region (6 complaints and 7 non-duplicative warranty claims) where 386,003 of the subject vehicles were sold.Ford did not find evidence of the lower intermediate shaft corrosion issue in these vehicles.Six of the vehicles had known prior collisions and the histories of the remaining 7 were unknown.To address concerns with possible steering separations in vehicles outside the region for safety recall 13V-385, Ford is conducting a Regional Program (13R01) to inspect and repair the steering assemblies of those vehicles as necessary.The lower intermediate shaft will be replaced only if it fails the inspection, the upper intermediate shaft will be repaired if it fails a Ford-specified measurement test.In the event the steering column lower bearings are found out of position, they will be re-seated and secured with a retaining clip.Based on Ford's field actions, this investigation is closed.The VOQs cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10505992, 10479893, 10477192, 10475950, 10474596
In the subject vehicles, the mechanical connection between the steering wheel and rack and pinion steering assembly consist of the steering column and an upper and lower intermediate shaft.A disconnection of any of these components from the steering system can create a loss of steering control.Allegations of a loss of steering control incidents reviewed during the Preliminary Evaluation PE12-025 appear to be related to a separation of the upper and lower shafts within the steering the column. In response to the Office of Defects Investigation's (ODI) Information Request (IR) during PE12-025, Ford provided 2 complaints and 9 warranty claims related to the alleged defect in the subject vehicles (see Figure 1 for an exemplar picture).ODI has received 5 complaints related to the alleged defect, including 1 related to an incident reported in one of the Ford complaints.The incident rate involving subject vehicles is 7.7 per 100,000 vehicles (15 total incidents).Five of the 15 incident vehicles were associated with a prior history report of a frontal impact incident.ODI also analyzed field data for MY 2005 through MY 2008 non-CVPI Crown Victoria and Grand Marquis models and MY 2009 through MY 2011 CVPI models, which use a similar steering column and intermediate shaft design. This analysis identified 4 reports from Ford and 2 complaints to ODI, including 1 duplicative of a complaint provided by Ford, resulting in 5 total incidents and an incident rate of 1.1 per 100,000 vehicles for a vehicle population of approximately 436,000 vehicles. In the peer vehicle analysis, 4 of 5 incident vehicles had a prior history report of a frontal impact incident.ODI also identified 42 reports (39 reports associated with subject vehicles and 3 reports associated peer vehicles) of the lower steering column shaft bearing displacement that did not result in complete separations of the upper to lower steering column shafts (see Figure 2). Vehicles with this condition were identified during inspections of police fleets or during vehicle repairs for complaints of looseness, binding or noise in the steering system while turning.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA13-004) has been opened to further assess the scope, frequency, consequence, and contributing factors to the steering column shaft separations.The VOQs associated with the opening of this investigation and a loss of steering control are: 10347404, 10474596, 10475950, 10477192, and 10479893.
On July 7, 2014 the Office of Defects Investigation (ODI) opened a preliminary evaluation based on five complaints (VOQs) alleging incidents ofinterference between dislodged exhaust manifold heat shields and the lower steering shaft/knuckle, including one alleging the interference resulted in a crash on a highway entrance ramp. Since opening this investigation, ODI has received four additional owner complaints.One indicated that the shield was removed before binding could occur.The other three occurred at low speed and produced some momentary steering binding that was overcome by the driver when additional steering effort was applied.Once the shield was repaired or removed, the steering returned to normal.The single incident ODI identified as a possible crash (VOQ No. 10578715) related to this condition could not be verified and the description of the crash in the complaint was not supported by the police accident report.No additional crash allegations have been identified related to the alleged defect condition.Information provided by Ford in its September 10, 2014 response to ODI's information request letter identified 10 additional incidents resulting in a low rate of 1.6 incidents per 100,000 vehicles sold in vehicles ranging from 7 to 11 years in service.Six of these incidents were reported by a single source, a state police fleet that corrected the problems in March 2011 and has not reported any additional failures since.Ford also reported 5 warranty claims, but these incidents occurred at very low mileages and appeared to be caused by loose or missing heat shield attachment hardware rather than the corrosion condition that was the cause of the more recent incidents and the focus of this investigation.This investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency will continue to monitor complaints and other information relating to the alleged defect in the subject vehicles and take further action in the future if warranted.The following VOQs are associated with this investigation:10643753, 10615584, 10611362, 10610451, 10578715, 10479681, 10471833, 10317493.
Showing up to 8 communication summaries and 4 investigations. Export coverage: communications received 2020–2026 only. Canadian applicability is not inferred. Consult NHTSA for full records.
Before You Buy
Questions to take to a seller or qualified mechanic.
Verify the VIN and ask the manufacturer to confirm applicability and completion of recall repairs.
Ask for documentation related to the official STEERING:RACK AND PINION:PINION SHAFT campaign (14V704000).
Ask for documentation related to the official STEERING campaign (13V385000).
Ask a mechanic to investigate any symptoms associated with reported categories; complaints alone are not a diagnosis.
Review service records and arrange an independent pre-purchase inspection.
A research brief for the 2006 Ford Crown Victoria, built from this report.
Record the VIN, market and exact powertrain. Confirm open recalls and completed remedies with the manufacturer.
Ask for repair documentation for campaign 14V704000 (STEERING:RACK AND PINION:PINION SHAFT). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 13V385000 (STEERING). A model-year match does not establish that this VIN is affected.
steering: 27 matched US complaint records mention this category. Ask the seller about related symptoms, prior diagnosis and documented repairs; ask an independent mechanic which checks fit this exact configuration.
vehicle speed control: 9 matched US complaint records mention this category. Ask the seller about related symptoms, prior diagnosis and documented repairs; ask an independent mechanic which checks fit this exact configuration.
air bags: 7 matched US complaint records mention this category. Ask the seller about related symptoms, prior diagnosis and documented repairs; ask an independent mechanic which checks fit this exact configuration.
Compare service records with the manufacturer’s schedule and arrange an independent pre-purchase inspection. This checklist is not a diagnosis or an expert inspection.