Open this section to check available listings. No listing request is made until you open it.
Source: Car Handshake and participating dealerships. Year, make and model must match to appear here; trims and specifications can differ. Listings do not establish vehicle condition or recall repair status.
Canadian owner complaints
Coverage, without substituted US totals.
Canadian complaint totals are not available in Recheck’s current dataset. This does not mean there are no complaints.
Canadian recalls come from Transport Canada and efficiency ratings from NRCan. US complaints and bulletins are optional context below; they do not establish Canadian applicability.
Canadian archive snapshot, including historical or superseded records.
Electrical
Issue:
This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships.
On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temp…
Read the complete source summary
Issue:
This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships.
On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt.
Note: This recall only affects the following block heater/cord part numbers:
C014003034 PK5A408J09 PU14000904
C014003151 PK5A408J13 PU14000905
C014000885 PK5A489J11 PU14000907
C014000888 PK5A489J22 PU14000909
C014000907 PK5A410H00 PU14000911
C014100904 PU14000900 PU14000913
C014100907 PU14000901 PU14003571
C014100911 PU14000902 PK5A489J14
PK5A408J05 PU14000903
Safety Risk:
Engine block heater wiring that overheats or melts could create the risk of a fire.
Corrective Actions:
Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater.
On certain vehicles, the rear wheel suspension link arms could separate. This could result in loss of vehicle control and cause a crash resulting in injury and/or damage to property. Correction: Dealers will replace both suspension link arms and encase them in…
Read the complete source summary
On certain vehicles, the rear wheel suspension link arms could separate. This could result in loss of vehicle control and cause a crash resulting in injury and/or damage to property. Correction: Dealers will replace both suspension link arms and encase them in epoxy to prevent future improper servicing. Note: This recall supersedes recall 2013327. As part of the previous recall, dealers were to inspect the suspension arms for corrosion, replace them depending on their condition, and encase them in epoxy. Only vehicles which did not receive replacement of both suspension arms through the previous recall will need to be repaired under this campaign.
On certain vehicles, in the event of a severe frontal collision, there is a possibility that the webbing of the seat belt in both second-row outboard seating positions could contact a portion of the metal seat cushion frame, become cut, and separate. If this o…
Read the complete source summary
On certain vehicles, in the event of a severe frontal collision, there is a possibility that the webbing of the seat belt in both second-row outboard seating positions could contact a portion of the metal seat cushion frame, become cut, and separate. If this occurs, the seat belt may not properly restrain the occupant, which could increase the risk of injury. Correction: Dealers will install plastic protectors on the seat cushion frame in both second-row outboard seating positions.
On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between…
Read the complete source summary
On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between the contact points, potentially resulting in an electrical short circuit. If a short circuit occurs, the switch assembly may overheat, produce smoke, melt and/or potentially lead to a fire causing injury and/or property damage. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. Note: This is an expansion of recall 2012-338.
On certain vehicles, electrical circuitry in the steering wheel assembly may become damaged. As a result, the driver's airbag may not function as intended, causing the instrument panel airbag warning lamp to illuminate. Failure of the driver's airbag to depl…
Read the complete source summary
On certain vehicles, electrical circuitry in the steering wheel assembly may become damaged. As a result, the driver's airbag may not function as intended, causing the instrument panel airbag warning lamp to illuminate. Failure of the driver's airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the seat occupant. Correction: Dealers will replace the spiral cable assembly.
On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation…
Read the complete source summary
On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the suspension arm threads for corrosion. If corrosion is found, the arm(s) will be replaced. If no corrosion is found, an epoxy sealer will be applied to the suspension arm to inhibit corrosion. Note: This recall supersedes recall 2012253. Vehicles that were repaired under the previous campaign will also need to be repaired under this campaign.
On certain vehicles, due to improperly applied grease, the driver's side power window master switch could stick or become inoperative. If attempts are made to lubricate the switch, the switch assembly could overheat and melt. A melting switch may produce smoke…
Read the complete source summary
On certain vehicles, due to improperly applied grease, the driver's side power window master switch could stick or become inoperative. If attempts are made to lubricate the switch, the switch assembly could overheat and melt. A melting switch may produce smoke and potentially lead to a fire causing property damage and/or personal injury. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary.
This recall was replaced by Transport Canada recall no. 2013-327.
On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of …
Read the complete source summary
This recall was replaced by Transport Canada recall no. 2013-327.
On some vehicles, if the rear wheel alignment toe adjustment locking nuts are improperly tightened when an alignment is performed in the field, backlash may develop in the threaded portion of the suspension arm (shaft and turnbuckle), followed by the formation of rust. If this occurs, threads may wear, causing the arm to separate which could result in loss of vehicle control. Correction: Dealers will inspect the arms and verify the tightening torque of the lock nuts, or replace the arms, as necessary.
On certain vehicles, the roll angle sensors in the airbag sensor assembly could fail. If one of the roll angle sensors malfunctions, the airbag warning lamp will illuminate, the roll detection system will be suspended, and the curtain shield airbag will not d…
Read the complete source summary
On certain vehicles, the roll angle sensors in the airbag sensor assembly could fail. If one of the roll angle sensors malfunctions, the airbag warning lamp will illuminate, the roll detection system will be suspended, and the curtain shield airbag will not deploy during a roll-over crash (where deployment is warranted), thereby increasing the risk of personal injuries to the seat occupant. The airbag system, however, will continue to detect frontal and lateral impacts and, in those instances, will function as designed. If both roll angle sensors fail nearly simultaneously after starting the vehicle, the curtain shield airbag and the seatbelt pretensioner could inadvertently deploy. Inadvertent curtain shield airbag deployment in a non-impact situation may cause damage to the surrounding vehicle environment and create expensive vehicle repair, including replacement of the curtain shield airbag module and the airbag electronic control unit. In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: Dealers will replace the airbag sensor assembly.
On certain vehicles, the accelerator pedal may become stuck in the wide open position due to an unsecured or incompatible driver's floor mat. A fully depressed accelerator pedal may result in very high vehicle speeds and make it difficult to slow or stop the …
Read the complete source summary
On certain vehicles, the accelerator pedal may become stuck in the wide open position due to an unsecured or incompatible driver's floor mat. A fully depressed accelerator pedal may result in very high vehicle speeds and make it difficult to slow or stop the vehicle. This could result in a crash causing property damage and/or personal injury. Correction: Dealers will modify or replace the accelerator pedal. Note: This is an expansion of recall 2009290 for vehicles not previously included in the campaign.
Model-year recalls do not establish repair completion.
Confirm open recalls with the manufacturer and ask a dealer whether the repairs are complete. Recheck’s VIN decoder identifies the vehicle; it does not provide recall repair status.
Use official test estimates with your own distance and prices.
Scenario estimate, not a live price quote or total cost of ownership. Uses the selected source configuration’s combined test consumption. Weather, speed, battery condition, charging losses, taxes, maintenance, depreciation and insurance can change actual cost. Plug-in hybrids are excluded from this simple calculator because fuel and electricity use depend on charging behaviour. Your inputs stay in your browser.
Coverage boundary: Canadian archive snapshot Exact normalized make/model/year safety matches. Efficiency retains explicitly named source configurations; spelling/configuration differences may exclude records. US complaint counts do not establish Canadian experience or the probability of a defect.
Accident history, current mechanical condition, ownership, liens, individual recall applicability, repair completion and battery health are not established by this model-year report. No failure rate or reliability score is calculated from raw complaint totals.
Specifications & Efficiency
Official source configurations. No trim is assumed.
Source configuration
Fuel / powertrain
Combined efficiency
Range
RAV4 AWD A4
X 2.4 L engine
10.5 L/100 km
Data unavailable
RAV4 AWD A5
X 3.5 L engine
11.0 L/100 km
Data unavailable
Official test estimates vary with configuration, driving and weather. Fuel codes are retained as published; US and Canadian test measures are shown in their source units. Plug-in hybrid source ranges and operating modes are shown separately; they are not added together.
More from the official configuration records
Figures belong to each source configuration. Test conditions and charging assumptions apply; tailpipe emissions exclude fuel and electricity production. No missing specifications are inferred.
RAV4 AWD · A4 — source specification details
Vehicle class
Sport utility vehicle
Engine displacement
2.4 L
Cylinders
4
City fuel consumption
11.5 L/100 km
Highway fuel consumption
9.3 L/100 km
Tailpipe CO₂ emissions
242 g/km
RAV4 AWD · A5 — source specification details
Vehicle class
Sport utility vehicle
Engine displacement
3.5 L
Cylinders
6
City fuel consumption
12.6 L/100 km
Highway fuel consumption
9.1 L/100 km
Tailpipe CO₂ emissions
253 g/km
Canadian defect investigations
Check the current official Transport Canada register.
Canadian investigation records are not imported into this report. Check the official register for affected vehicles, investigation details and current status; no match or status is implied here.
A research brief for the 2007 Toyota RAV4, built from this report.
Record the VIN, market and exact powertrain. Confirm open recalls and completed remedies with the manufacturer.
Ask for repair documentation for campaign 2021723 (Electrical). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 2016398 (Suspension). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 2016075 (Seats And Restraints). A model-year match does not establish that this VIN is affected.
Compare service records with the manufacturer’s schedule and arrange an independent pre-purchase inspection. This checklist is not a diagnosis or an expert inspection.
Optional US contextNHTSA complaints, communications and investigations · not Canadian records
These are US records. Models, equipment, campaigns and driving conditions can differ. Counts are not Canadian complaint totals, verified reviews or reliability ratings.
Reported Problem Categories
US NHTSA complaints for the 2007 Toyota RAV4.
STEERING
271
ENGINE
195
SUSPENSION
125
VEHICLE SPEED CONTROL
101
AIR BAGS
99
US context, not Canadian complaint counts. NHTSA documents known discrepancies in its bulk complaint file. Consumer allegations are not confirmed defects. One complaint can mention several categories. Counts are not failure rates.
Reports Over Time
US complaints by filing month, latest 12 observed months.
24-01
24-05
24-10
24-12
25-03
25-04
25-05
25-06
25-09
25-10
26-01
26-09
A month with no bar is not evidence that no problems occurred. Publication and reporting delays affect totals.
Read chart data
2024-01
1
2024-05
2
2024-10
1
2024-12
1
2025-03
1
2025-04
1
2025-05
2
2025-06
1
2025-09
2
2025-10
1
2026-01
1
2026-09
1
RECHECK EVIDENCE LAB
The mileage lens
Where the available US complaint records fall by reported mileage.
Reported mileage at incident
Matched complaint records
Below 25,000 mi
117
25,000–49,999 mi
191
50,000–99,999 mi
305
100,000–149,999 mi
155
150,000+ mi
40
Missing or excluded mileage
196
808 of 1,004 matched complaints have positive, usable mileage. Source zero values can represent missing information and are excluded; values above 1.5 million miles are excluded. These are selected allegations with no vehicle-population denominator. The table cannot predict when your vehicle will fail. Mileage is retained in US source miles.
Crash flagged53US complaint allegations
Fire flagged37US complaint allegations
Towed flagged6US complaint allegations
Positive source flags are counted per deduplicated complaint, not verified incidents. Categories and flags can overlap; an unflagged or missing value does not prove an incident did not occur.
Bulletins & Investigations
US official records; applicability in Canada is not established.
51 matched manufacturer communications · 4 matched investigations. Communications are not necessarily recalls or technical service bulletins.
EA12006 · Power Window Master Switch Fire
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Showing up to 8 communication summaries and 4 investigations. Export coverage: communications received 2020–2026 only. Canadian applicability is not inferred. Consult NHTSA for full records.
Sources & Last Updated
Trace the evidence behind this report.
Transport Canada Vehicle Recalls Database · Original source · Evidence updated Nov 17, 2026
US NHTSA complaints · optional US context only · Original source · Retrieved Nov 17, 2026 · Counts deduplicated by ODI number.