Open this section to check available listings. No listing request is made until you open it.
Source: Car Handshake and participating dealerships. Year, make and model must match to appear here; trims and specifications can differ. Listings do not establish vehicle condition or recall repair status.
Canadian owner complaints
Coverage, without substituted US totals.
Canadian complaint totals are not available in Recheck’s current dataset. This does not mean there are no complaints.
Canadian recalls come from Transport Canada and efficiency ratings from NRCan. US complaints and bulletins are optional context below; they do not establish Canadian applicability.
Canadian archive snapshot, including historical or superseded records.
Powertrain
Issue:
On certain vehicles, the paint on the front axle shafts could become damaged. As a result, the axle shaft(s) could corrode. If this happens, the axle shaft(s) could break and cause a loss of power to the wheels. Additionally, if the vehicle is parked a…
Read the complete source summary
Issue:
On certain vehicles, the paint on the front axle shafts could become damaged. As a result, the axle shaft(s) could corrode. If this happens, the axle shaft(s) could break and cause a loss of power to the wheels. Additionally, if the vehicle is parked and the parking brake isn't applied, the vehicle could roll away.
Note: This recall is an expansion of recall HO54 (Transport Canada recall no. 2020-609).
Safety Risk:
A loss of power to the wheels could increase the risk of a crash. A parked vehicle that moves suddenly could create a risk of a crash or an injury.
Corrective Actions:
Honda will notify owners by mail and advise you to take your vehicle to a dealership to inspect and, if necessary, replace the axle shaft(s).
Issue:
On certain vehicles, the paint on the front axle shafts could delaminate or become damaged by road debris. As a result the axle shaft could corrode. If this happens, the axle shafts could break and cause a loss of power to the wheels. Also, if this hap…
Read the complete source summary
Issue:
On certain vehicles, the paint on the front axle shafts could delaminate or become damaged by road debris. As a result the axle shaft could corrode. If this happens, the axle shafts could break and cause a loss of power to the wheels. Also, if this happens and the vehicle is parked without the parking brake applied, the vehicle could roll away.
Safety Risk:
A loss of power to the wheels or a vehicle rollaway could increase the risk of a crash.
Corrective Actions:
Honda will notify owners by mail and instruct you to take your vehicle to a dealer to inspect, and if necessary, replace both axle shafts.
On certain vehicles, the case for the battery sensor may have been improperly manufactured with gaps that could allow for moisture intrusion. If moisture or road salt were to enter the battery sensor case, it could result in corrosion to the sensor, which coul…
Read the complete source summary
On certain vehicles, the case for the battery sensor may have been improperly manufactured with gaps that could allow for moisture intrusion. If moisture or road salt were to enter the battery sensor case, it could result in corrosion to the sensor, which could cause an electrical short, increasing the risk of a fire causing injury and/or property damage. Correction: Dealers will inspect, and replace the battery sensor as necessary.
On certain vehicles, the fuel tank may have been manufactured incorrectly and could leak. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will replace the fuel ta…
Read the complete source summary
On certain vehicles, the fuel tank may have been manufactured incorrectly and could leak. Fuel leakage, in the presence of an ignition source, could result in a fire causing property damage and/or personal injury. Correction: Dealers will replace the fuel tank.
Model-year recalls do not establish repair completion.
Confirm open recalls with the manufacturer and ask a dealer whether the repairs are complete. Recheck’s VIN decoder identifies the vehicle; it does not provide recall repair status.
Use official test estimates with your own distance and prices.
Scenario estimate, not a live price quote or total cost of ownership. Uses the selected source configuration’s combined test consumption. Weather, speed, battery condition, charging losses, taxes, maintenance, depreciation and insurance can change actual cost. Plug-in hybrids are excluded from this simple calculator because fuel and electricity use depend on charging behaviour. Your inputs stay in your browser.
Coverage boundary: Canadian archive snapshot Exact normalized make/model/year safety matches. Efficiency retains explicitly named source configurations; spelling/configuration differences may exclude records. US complaint counts do not establish Canadian experience or the probability of a defect.
Accident history, current mechanical condition, ownership, liens, individual recall applicability, repair completion and battery health are not established by this model-year report. No failure rate or reliability score is calculated from raw complaint totals.
Specifications & Efficiency
Official source configurations. No trim is assumed.
Source configuration
Fuel / powertrain
Combined efficiency
Range
Accord AV
X 2.4 L engine
8.0 L/100 km
Data unavailable
Accord AV7
X 2.4 L engine
8.0 L/100 km
Data unavailable
Accord M6
X 2.4 L engine
8.6 L/100 km
Data unavailable
Accord A6
X 3.5 L engine
9.2 L/100 km
Data unavailable
Accord AS6
X 3.5 L engine
9.6 L/100 km
Data unavailable
Accord M6
X 3.5 L engine
10.9 L/100 km
Data unavailable
Official test estimates vary with configuration, driving and weather. Fuel codes are retained as published; US and Canadian test measures are shown in their source units. Plug-in hybrid source ranges and operating modes are shown separately; they are not added together.
More from the official configuration records
Figures belong to each source configuration. Test conditions and charging assumptions apply; tailpipe emissions exclude fuel and electricity production. No missing specifications are inferred.
Accord · AV — source specification details
Vehicle class
Mid-size
Engine displacement
2.4 L
Cylinders
4
City fuel consumption
9.1 L/100 km
Highway fuel consumption
6.6 L/100 km
Tailpipe CO₂ emissions
184 g/km
Accord · AV7 — source specification details
Vehicle class
Mid-size
Engine displacement
2.4 L
Cylinders
4
City fuel consumption
9.1 L/100 km
Highway fuel consumption
6.6 L/100 km
Tailpipe CO₂ emissions
184 g/km
Accord · M6 — source specification details
Vehicle class
Mid-size
Engine displacement
2.4 L
Cylinders
4
City fuel consumption
10.0 L/100 km
Highway fuel consumption
6.8 L/100 km
Tailpipe CO₂ emissions
198 g/km
Accord · A6 — source specification details
Vehicle class
Mid-size
Engine displacement
3.5 L
Cylinders
6
City fuel consumption
11.1 L/100 km
Highway fuel consumption
6.8 L/100 km
Tailpipe CO₂ emissions
212 g/km
Accord · AS6 — source specification details
Vehicle class
Mid-size
Engine displacement
3.5 L
Cylinders
6
City fuel consumption
11.4 L/100 km
Highway fuel consumption
7.3 L/100 km
Tailpipe CO₂ emissions
221 g/km
Accord · M6 — source specification details
Vehicle class
Mid-size
Engine displacement
3.5 L
Cylinders
6
City fuel consumption
13.0 L/100 km
Highway fuel consumption
8.5 L/100 km
Tailpipe CO₂ emissions
251 g/km
Canadian defect investigations
Check the current official Transport Canada register.
Canadian investigation records are not imported into this report. Check the official register for affected vehicles, investigation details and current status; no match or status is implied here.
A research brief for the 2013 Honda Accord, built from this report.
Record the VIN, market and exact powertrain. Confirm open recalls and completed remedies with the manufacturer.
Ask for repair documentation for campaign 2025340 (Powertrain). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 2020609 (Powertrain). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 2017327 (Electrical). A model-year match does not establish that this VIN is affected.
Compare service records with the manufacturer’s schedule and arrange an independent pre-purchase inspection. This checklist is not a diagnosis or an expert inspection.
Optional US contextNHTSA complaints, communications and investigations · not Canadian records
These are US records. Models, equipment, campaigns and driving conditions can differ. Counts are not Canadian complaint totals, verified reviews or reliability ratings.
Reported Problem Categories
US NHTSA complaints for the 2013 Honda Accord.
STEERING
500
ELECTRICAL SYSTEM
417
ENGINE
179
UNKNOWN OR OTHER
120
SERVICE BRAKES
111
US context, not Canadian complaint counts. NHTSA documents known discrepancies in its bulk complaint file. Consumer allegations are not confirmed defects. One complaint can mention several categories. Counts are not failure rates.
Reports Over Time
US complaints by filing month, latest 12 observed months.
25-11
25-12
26-01
26-02
26-03
26-04
26-05
26-06
26-07
26-09
26-10
26-11
A month with no bar is not evidence that no problems occurred. Publication and reporting delays affect totals.
Read chart data
2025-11
3
2025-12
3
2026-01
8
2026-02
6
2026-03
2
2026-04
2
2026-05
4
2026-06
3
2026-07
4
2026-09
4
2026-10
5
2026-11
1
RECHECK EVIDENCE LAB
The mileage lens
Where the available US complaint records fall by reported mileage.
Reported mileage at incident
Matched complaint records
Below 25,000 mi
285
25,000–49,999 mi
203
50,000–99,999 mi
275
100,000–149,999 mi
88
150,000+ mi
33
Missing or excluded mileage
544
884 of 1,428 matched complaints have positive, usable mileage. Source zero values can represent missing information and are excluded; values above 1.5 million miles are excluded. These are selected allegations with no vehicle-population denominator. The table cannot predict when your vehicle will fail. Mileage is retained in US source miles.
Crash flagged68US complaint allegations
Fire flagged9US complaint allegations
Towed flagged45US complaint allegations
Positive source flags are counted per deduplicated complaint, not verified incidents. Categories and flags can overlap; an unflagged or missing value does not prove an incident did not occur.
Bulletins & Investigations
US official records; applicability in Canada is not established.
8 matched manufacturer communications · 5 matched investigations. Communications are not necessarily recalls or technical service bulletins.
DP20005 · Loss of Direction Control
The Office of Defects Investigation (ODI) received a petition dated October 19, 2020 requesting an investigation of an alleged defect in the steering system in Model Year (MY) 2013 Honda Accord vehicles. The petitioner alleges that MY2013 Honda accord vehicles are experiencing a sudden loss of steering control as the vehicle veers from its intended path of travel. The petitioner further alleges that this deviation from the intended path of travel occurs without warning or driver input while operating the vehicle under normal driving conditions. The petition itself can be reviewed at NHTSA.gov under ODI Number 11349961.On November 23, 2020, ODI opened a Defect Petition (DP20-005) to evaluate whether to grant or deny the petition. ODI sent two Information Request (IR) letters to Honda requesting information on steering anomalies in MY2013 Honda Accord vehicles and later MY2014-2015 Honda Accord vehicles.ODI performed extensive analysis on the information obtained from Honda as well as information in NHTSA's database.Based on ODI's review of the applicable materials, including responses to the IR letters sent to Honda, Vehicle Owner Questionnaires (VOQ) and Early Warning Reporting data, NHTSA has decided to grant the petition. ODI has opened an Engineering Analysis (EA21-001) to assess the scope, frequency and potential safety related consequences of the alleged defect, a sudden loss of steering control.The ODI complaints cited above can be viewed at www.NHTSA.gov under the following ODI identification numbers:11414105, 11406220, 11398736, 11387462 ,11387075, 11387049, 11375580, 11364698 ,11361125, 11351660, 11349961, 11327909, 11327170, 11324181, 11306112, 11301957, 11289067, 11282525, 11278511, 11277659, 11258017, 11256914, 11218752, 11208077, 11196050, 11194358, 11189901, 11165075, 11163481, 11156378, 11154891, 11131050
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
On May 6, 2021, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA21-001) to assess a sudden loss of steering control, in Model Year (MY) 2013-2015 Honda Accord vehicles. Consumers alleged while driving the steering wheel would pull to the left or the right independently. Steering pull may pose a risk of loss of directional control. Honda stated that they believed the inadvertent steering input was caused by a loose magnet located within the electronic power steering (EPS) system. Due to poor formulation of the adhesive, this magnet can become loose and move up to 2 degrees around the steering column. When the magnet moves, the torque sensor generates a signal that results in unwanted steering in either direction. Honda stated the steering force required to maintain directional control with a loose magnet is a maximum of 3-pound feet. The maximum force of the unwanted steering input can be overcome by the driver and is similar to driving on grooved pavement.The Vehicle Research Test Center (VRTC) sent over 4,000 questionnaires to 2013-2015 Honda Accord vehicle owners. Of the 637 responses, 58 consumers experienced unwanted steering. Consumers experiencing unwanted steering did not report difficulties maintaining directional control. There were no crashes or injuries reported to VRTC. Testing done by VRTC was not able to reproduce the allegations. Analysis of all relevant data indicates that the subject condition has a relatively low failure rate. The poor adhesive formulation was addressed by the supplier with three (3) counter measures in the manufacturing process.There has been a declining trend in consumer complaints to NHTSA which indicates possible exhaustion of parts prone to failure. In view of the low rate, declining complaint trend, the nature of failure, and resolution of the adhesive formulation, this Engineering Analysis is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.The ODI complaints cited above can be viewed at www.NHTSA.gov under the following ODI identification numbers: 11538714, 11528538, 11528008, 11522953, 11496557, 11495837, 11494328, 11478680, 11477167, 11476758, 11476263, 11471198, 11470001, 11467026, 11466561, 11466016, 11465626, 11464143, 11463558, 11462759, 11461500, 11460777, 11460191, 11455540, 11454334, 11452198, 11448114, 11447666, 11444888, 11444823, 11444172, 11443324, 11443243, 11443105, 11441374, 11439520, 11438345, 11437261, 11436824, 11436350, 11435994, 11435079, 11434969, 11434545, 11434442, 11434381, 11433824, 11433745, 11433555, 11433368, 11433176, 11431206, 11430465, 11430253, 11430009, 11429253, 11428301, 11427449, 11426841, 11426340, 11425928, 11425261, 11425230, 11423611, 11423245, 11422445, 11422395, 11422351, 11422220, 11422138, 11422069, 11421683, 11421589, 11421540, 11420573, 11419338, 11419270, 11418147, 11418143, 11417768, 11417742, 11417570, 11417437, 11416804, 11416699, 11416401, 11416378, 11416375, 11416155, 11416117, 11416084, 11416051, 11416032, 11416028, 11416024, 11416000, 11415933, 11415915, 11414105, 11406220, 11398736 ,11387075, 11387049, 11375580, 11364698, 11361125, 11351660, 11349961, 11327909, 11327170, 11301957, 11289067, 11282525, 11277659, 11258017, 11256914, 11218752, 11208077, 11196050, 11194358, 11189901, 11165075, 11163481, 11154891
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Showing up to 8 communication summaries and 4 investigations. Export coverage: communications received 2020–2026 only. Canadian applicability is not inferred. Consult NHTSA for full records.
Sources & Last Updated
Trace the evidence behind this report.
Transport Canada Vehicle Recalls Database · Original source · Evidence updated Nov 17, 2026
US NHTSA complaints · optional US context only · Original source · Retrieved Nov 17, 2026 · Counts deduplicated by ODI number.