Open this section to check available listings. No listing request is made until you open it.
Source: Car Handshake and participating dealerships. Year, make and model must match to appear here; trims and specifications can differ. Listings do not establish vehicle condition or recall repair status.
Canadian owner complaints
Coverage, without substituted US totals.
Canadian complaint totals are not available in Recheck’s current dataset. This does not mean there are no complaints.
Canadian recalls come from Transport Canada and efficiency ratings from NRCan. US complaints and bulletins are optional context below; they do not establish Canadian applicability.
Canadian archive snapshot, including historical or superseded records.
Other
Issue:
This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones.
Note: …
Read the complete source summary
Issue:
This recall is for aftermarket replacement rear window glass produced by Vitro Automotriz. Certain rear window glass may not have been properly tempered. If the window breaks, the glass may separate into large pieces instead of very small ones.
Note: This is a voluntary recall that is not being conducted under the requirements of the Motor Vehicle Safety Act.
Safety Risk:
Glass that breaks in to large pieces could create a risk of injury.
Corrective Actions:
The company will notify consumers by mail and instruct them to inspect the designation code marked on the rear window glass. Products affected by this recall have the designation “DOT 287” along with the lettering “VMR” (Replacement Market) and a date code that is before July 2019. This information is printed on the bottom corner of the glass. Consumers should contact Vitro's customer service at 1-412-995-6457 or argbacklites@vitro.com to arrange for replacement of the glass.
On certain vehicles equipped with diesel engines, service replacement steering gears, installed after June 30, 2014, may not properly mount to the frame rail due to insufficient clearance. This could result in insufficient clamp load on the joints, which over…
Read the complete source summary
On certain vehicles equipped with diesel engines, service replacement steering gears, installed after June 30, 2014, may not properly mount to the frame rail due to insufficient clearance. This could result in insufficient clamp load on the joints, which over time may cause fatigue of one or more of the steering gear retention bolts. If the steering gear bolts were to fatigue, one or more of the bolts could fracture, which could result in a loss of steering control, increasing the risk of a crash causing injury and/or damage to property. Correction: Dealers will install spacers between the gear and the frame rail to add clearance and ensure adequate clamp load to the joints.
Model-year recalls do not establish repair completion.
Confirm open recalls with the manufacturer and ask a dealer whether the repairs are complete. Recheck’s VIN decoder identifies the vehicle; it does not provide recall repair status.
Coverage boundary: Canadian archive snapshot Exact normalized make/model/year safety matches. Efficiency retains explicitly named source configurations; spelling/configuration differences may exclude records. US complaint counts do not establish Canadian experience or the probability of a defect.
Accident history, current mechanical condition, ownership, liens, individual recall applicability, repair completion and battery health are not established by this model-year report. No failure rate or reliability score is calculated from raw complaint totals.
Specifications & Efficiency
Official source configurations. No trim is assumed.
No exact vehicle configuration match in the imported efficiency dataset. No estimate is substituted.
Canadian defect investigations
Check the current official Transport Canada register.
Canadian investigation records are not imported into this report. Check the official register for affected vehicles, investigation details and current status; no match or status is implied here.
A research brief for the 2008 Ford F-250, built from this report.
Record the VIN, market and exact powertrain. Confirm open recalls and completed remedies with the manufacturer.
Ask for repair documentation for campaign 2019420 (Other). A model-year match does not establish that this VIN is affected.
Ask for repair documentation for campaign 2015081 (Steering). A model-year match does not establish that this VIN is affected.
Compare service records with the manufacturer’s schedule and arrange an independent pre-purchase inspection. This checklist is not a diagnosis or an expert inspection.
Optional US contextNHTSA complaints, communications and investigations · not Canadian records
These are US records. Models, equipment, campaigns and driving conditions can differ. Counts are not Canadian complaint totals, verified reviews or reliability ratings.
Reported Problem Categories
US NHTSA complaints for the 2008 Ford F-250.
STEERING
80
SUSPENSION
35
ENGINE
19
TIRES
16
ENGINE AND ENGINE COOLING
15
US context, not Canadian complaint counts. NHTSA documents known discrepancies in its bulk complaint file. Consumer allegations are not confirmed defects. One complaint can mention several categories. Counts are not failure rates.
Reports Over Time
US complaints by filing month, latest 12 observed months.
24-06
24-08
24-10
24-11
24-12
25-06
25-07
25-11
25-12
26-02
26-09
26-10
A month with no bar is not evidence that no problems occurred. Publication and reporting delays affect totals.
Read chart data
2024-06
1
2024-08
1
2024-10
3
2024-11
1
2024-12
1
2025-06
1
2025-07
1
2025-11
1
2025-12
1
2026-02
1
2026-09
1
2026-10
1
RECHECK EVIDENCE LAB
The mileage lens
Where the available US complaint records fall by reported mileage.
Reported mileage at incident
Matched complaint records
Below 25,000 mi
20
25,000–49,999 mi
40
50,000–99,999 mi
38
100,000–149,999 mi
34
150,000+ mi
29
Missing or excluded mileage
36
161 of 197 matched complaints have positive, usable mileage. Source zero values can represent missing information and are excluded; values above 1.5 million miles are excluded. These are selected allegations with no vehicle-population denominator. The table cannot predict when your vehicle will fail. Mileage is retained in US source miles.
Crash flagged10US complaint allegations
Fire flagged4US complaint allegations
Towed flagged9US complaint allegations
Positive source flags are counted per deduplicated complaint, not verified incidents. Categories and flags can overlap; an unflagged or missing value does not prove an incident did not occur.
Bulletins & Investigations
US official records; applicability in Canada is not established.
1 matched manufacturer communications · 1 matched investigations. Communications are not necessarily recalls or technical service bulletins.
PE13014 · Alleged Loss of Steering
The Office of DefectsInvestigation (ODI) opened PE13-014 after identifying five complaints alleging steering gear failure in model year (MY) 2008 Ford F-250 and F-350 Super Duty pick-up trucks and to evaluate the relationship between the design history of the steering gear assembly and the alleged defect.As background, ODI investigated steering gear sector shaft fractures in approximately 1.3 million MY 1999 - 2001 Ford Super Duty pick-up trucks and MY 2000 - 2001 Ford Excursion sport utility vehicles in Engineering Analysis EA01-009.The investigation determined that the sector shaft failures were the result of extraordinary, possibly multiple, impacts and not the result of fatigue.No defect in design, manufacturing or materials was identified in the sector shaft.EA01-009 was closed August 19, 2003 with 169 complaints, resulting in a rate of 12.9 incidents per 100,000 vehicles after approximately one year of service.Ford increased the diameter of the sector shaft from 1.375 inches to 1.625 inches at the start of MY 2005 production, increasing the resistance of the steering gear assembly to torsional overload by approximately 48% and changing the failure mode from sector shaft fracture to cracked or broken sector shaft gear teeth.The redesigned steering gear assembly was used in approximately 1.1 million MY 2005 through 2009 Ford Super Duty pick-up trucks, including the subject vehicles.Figure 1 shows the basic steering system design used in Ford Super Duty trucks investigated in EA01-009 and PE13-014. Figure 2 shows the locations of failures resulting from impact related torsional overloading of the sector shaft for the subject vehicles and the prior generation Ford Super Duty trucks investigated in EA01-009.Figure 3 shows an example of a failed sector shaft investigated in EA01-009 and comparisons of fracture surfaces of sector shafts failing from fatigue loading and from torsional overload.Ford provided field return part analysis of failed steering gears from MY 2005 through 2009 Super Duty trucks found evidence of broken sector shaft gear teeth and piston damage consistent with incidents of single event overload (Figure 4).Laboratory analysis found no evidence of fatigue or material property defects in any of the fractures.Analysis of complaint rates by vehicle build month showed no patterns indicating potential manufacturing quality issues and no difference before and after Ford introduced design changes to the input shaft and sector shaft seals in July 2007 to address potential leak concerns (Figure 5).Analysis of failures by time in service indicates a random failure pattern/distribution, consistent with incidents of impact induced overload (Figure 6). The complaint rate for the subject vehicles after approximately 5 to 6 years, 7.1 incidents per 100,000 vehicles, is lower than the rate observed in EA01-009. Furthermore, similar to the condition investigated in EA01-009, a number of incident records include evidence of impact loads (e.g., curb strikes) and several alleged crashes include incidents in which information suggests that the steering gear failure was most likely a result of crash forces, rather than the cause of the crash.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.The ODI complaints cited above can be reviewed at ww
Showing up to 8 communication summaries and 4 investigations. Export coverage: communications received 2020–2026 only. Canadian applicability is not inferred. Consult NHTSA for full records.
Sources & Last Updated
Trace the evidence behind this report.
Transport Canada Vehicle Recalls Database · Original source · Evidence updated Nov 17, 2026
US NHTSA complaints · optional US context only · Original source · Retrieved Nov 17, 2026 · Counts deduplicated by ODI number.